1. When cleaning the High Ice Efficiency Flake Ice Machine, the power should be turned off. It is strictly forbidden to use the water pipe to directly align with the body. Use a neutral detergent to scrub. Do not use acidic or alkaline solvents to clean.

2. The ice machine must unscrew the inlet hose head for two months to clean the inlet valve screen to prevent the sand mud impurities from clogging the water inlet, which causes the water intake to become smaller, resulting in no ice.

3. The Flake Ice Machine must clean the surface of the condenser every two months. If the condensation is poor, the compressor components will be damaged. When cleaning, use a vacuum cleaner, a small brush, etc. to clean the condensed surface oil dust. Do not use a sharp metal tool to clean it to avoid damaging the condenser.

4. The water pipes, sinks, storage refrigerators and protective film of the ice machine should be cleaned every two months.

5. When the ice machine is not in use, it should be cleaned, and the ice mold and the moisture in the box should be dried with a hair dryer, placed in a place free of corrosive gas and ventilated and dry, to avoid open storage.

1, the High Ice Efficiency Flake Ice Machine should be installed away from the heat source, no direct sunlight, good ventilation, the ambient temperature should not exceed 35 degrees Celsius, to prevent the ambient temperature is too high, resulting in poor condenser heat dissipation, affecting the ice making effect. The floor on which the ice machine is installed should be solid and flat, and the ice machine must be level, otherwise it will cause no ice and noise during operation.

2. The gap between the back and left and right sides of the Seafood Markets Flake Ice Machine should be no less than 30cm, and the top gap should be no less than 60cm.

3, the ice machine should use independent power supply, dedicated line power supply and equipped with fuses and leakage protection switches, and must be reliably grounded.

4. The water of the ice machine should conform to the national drinking water standard, and a water filtration device should be installed to filter the impurities in the water to avoid blocking the water pipe and polluting the water tank and the ice mold. And affect the performance of ice making.

The sliced ice produced by the Stable Performance Flake Ice Machine has low temperature, light weight, dryness and no powder. It is suitable for the preservation of seafood in major supermarkets and stores. The flake ice not only makes the cold collection not dehydrated, but also maintains its original color, and because the flake ice is smooth and non-angular, it will not scratch the skin of the cold collection, ensuring the original flavor of the cold collection, vegetable and seafood transportation. In order to ensure the freshness, a certain amount of flake ice make by 5 Ton Flake Ice Machine also plays the role of preserving freshness. At the same time, in the ocean fishing, because of the characteristics of flake ice, it can maintain relatively long-term freshness with the ice-preserved seafood, which is convenient for the ocean Fishing.

In Seawater Slurry Ice Machine, through the inlet valve, the water  automatically enters a water storage tank, and then pumps water to the diverter  through the water pump. The diverter pipe uniformly flows the water to the  evaporator cooled by the low-temperature liquid refrigerant, and the water is  cooled to the freezing point, which is cooled to the freezing point. The water  will solidify into ice, and the water that has not been frozen by the evaporator  flows into the water reservoir again, and the circulation is resumed by the  water pump.

When the ice cube reaches the required thickness, it enters the deicing  state, and the high pressure hot gas discharged from the Stable Performance  Flake Ice Machine is led to the evaporator through the reversing valve to  replace the low temperature liquid refrigerant. This forms a water film between  the ice cube and the evaporator, which leaves the ice cubes out of the  evaporator, and the ice cubes fall freely into the ice storage tank by  gravity.

The PLC Controller Flake Ice Machine is divided according to the water source, and can be divided into fresh water flake ice machine and sea water flake ice machine. However, the freshwater flake ice machine will also add a certain proportion of salt water, the concentration of which is far lower than that of sea water. The purpose of adding salt is to make the borneol easier to form, improve the quality of the borneol, the borneol size is suitable, more beautiful, and the borneol is more likely to fall off. Protect equipment and consume less electricity. If there is no salt, the flake ice will make a harsh sound.

Press the start/stop button to start the 2T Flake Ice Machine, add salt according to the above salt addition ratio, fill the salt water tank with water and stir evenly, then put the salt water pump into the liquid tube and put it into the salt water tank.

After adding salt, observe the operation of the ice machine, the size of the ice and the quality of the ice. If the ice flakes produced by the ice machine are found to be broken, the ice machine is accompanied by a sharp ice-splitting sound, indicating that the brine is not added to the water tank. A common problem is the presence of air in the inlet and outlet tubes, which affects the accuracy of the metering and salting of the brine pump. At this point, the air inside the tube should be removed. The correct way is to suck the air out of the saline pump outlet tube. When you feel salt water in your mouth, check if the brine pump outlet tube has water droplets. If there is water evenly dripping out to indicate normal, then insert the saline pump outlet tube into the water tank.

According to the application and the characteristics of the ice itself, the 5T Flake Ice Machine is mainly divided into: tube ice, flake ice (fresh water/sea water), block ice, granular ice, plate ice (fresh water/sea water), transparent ice, ice water. No matter which type of ice, it is determined by its characteristics. According to the shape of ice, it can be divided into: scaly ice machine, tube ice machine, snowflake ice machine, ice machine (can be divided into small ice machine and industrial large ice machine), ice machine, ice machine, Ice pellet machine, pellet machine, bullet ice machine, Stable Performance Flake Ice Machine.

The temperature sensor on the condenser works like this. When the temperature on the condenser is too high, the cooling effect of the fan motor is too late to cool. At this time, the temperature felt by the temperature sensor is too high, and the simulation is performed by A/D conversion. The signal is converted into a digital signal, judged by the program, and the command is issued to control whether the relay of the compressor motor is correspondingly controlled, and finally the working state of the compressor is controlled. Any refrigeration system is inseparable from the important accessories of the condenser, and Ice Ice’s ice machine is no exception. The condenser can be divided into an air-cooled condenser and a water-cooled condenser according to the heat exchange mode. The air-cooled condenser circulates air through a fan to achieve cooling.

The condenser should be cleaned regularly, otherwise it will cause a reduction in the amount of ice and failure.

1. Clean the condenser fins from top to bottom with a soft brush. Do not brush left or right to avoid bending the heat sink.

2. If there is oil on the heat sink of the condenser, it can be cleaned with a certain proportion of special detergent.

3. Clean the filter with neutral soapy water or detergent to ensure that the mesh is free of dust or dirt. Depending on the quality of the environment, it is usually cleaned once every 1-2 months.

The flake ice machine is a professional high-volume ice making operation tool and has high quality ice making efficiency. Therefore, it can be widely used in supermarkets or meat and aquatic products processing enterprises. Fresh Water Flake Ice Machine Supplier will introduce the several areas of use for the flake ice machine:

1. Supermarket preservation

It is well known that supermarkets often need a large amount of borneol or ice cubes for fresh-keeping in seafood or fresh meat. Not only can the foods be stored for a longer period of time without qualitative changes. so it is necessary to use High Ice Efficiency Flake Ice Machine to make a large number of products. The borneol prevents food damage and maximizes the freshness of each product.

2. Poultry processing

In the field of poultry processing, the flake ice machine is often used for preservation. During the whole process of poultry processing, due to the influence of high temperature steam, it will have a certain impact on the taste of all fresh meat. Therefore, it is necessary to use a flake ice machine to make a large number of borneols to quickly lower the temperature to ensure the tender taste of the meat.

3. Preservation of vegetables and fruits

Many merchants also use ice machine in order to better preserve vegetables or fruits. By making large quantities of borneol, they can better preserve vegetables and fruits, and can maintain their natural quality or food safety to the utmost extent. The natural cold source and wet and cold storage of the flake ice machine not only keep fresh and effective, but also keep the fruits and vegetables intact for a long time.

1. The Flake Ice Machine adopts the PLC programmable control system to realize the control. The running performance is stable, safe and reliable. The user can control the automatic start and automatic stop time of the flake ice machine according to the power consumption to save energy and fully automatic control.

2, compared with other ice machines, the ice machine is fast, the ice can be made in 1 minute, the ice is continuous, and it is easy to use.

3, the cost is low, the production cost of ice is very economical, it takes only about 80 degrees of electricity to cool 16 degrees Celsius water into 1 ton of ice.

4, the Flake Ice Machine 5T is equipped with a variety of protection devices such as high and low pressure, water cut, limit, overload, etc., which further enhances the safety and stability of the ice machine, allowing the user to directly stop power and stop making ice when no ice is needed. The internal structure of the evaporator is simple, and the components have high versatility, so the operation is reliable, the maintenance is convenient, and the maintenance is easy.

5. The flake ice machine adopts fully automatic control, and the operator can operate by pressing the switch. The evaporator materials are made of imported 304 stainless steel or heat-transfer efficient carbon steel surface plating hard enamel to ensure the super corrosion resistance of the ice bucket and the cleanliness of the borneol.

Proper use of the Fresh Water Flake Ice Machine can reduce the failure rate of the ice machine and increase the service life of the ice machine. Ice machine equipment also requires regular maintenance and cleaning to improve the life of the ice machine. How to clean and maintain.

1. When cleaning the Seafood Markets Flake Ice Machine, turn off the power supply. Do not use the water pipe to directly align with the body of the ice machine. Use clean water and add a proper amount of neutral detergent (do not use acidic, alkaline and other corrosive solvents). Ice machine equipment coamings and liners, then rubbed with a cloth.

2, the ice machine must be opened twice a month to open the inlet hose head, clean the inlet valve filter, to avoid the cement impurities in the water block the water inlet, the surface caused the water to become smaller, the water is not enough, the water pressure is insufficient, leading to ice making The machine does not make a machine.

3. The condenser surface must be cleaned in the second month. Do not use a sharp metal tool to clean it to avoid damaging the condenser.

4. The water pipes, sinks, storage refrigerators and protective film of the ice machine should be cleaned once every two months. When not in use, it should be cleaned, and the ice mold and the moisture in the box should be dried with a hair dryer, and placed in a place where there is no corrosive gas and air and dry, avoiding open storage.

The ice machine equipment is just like ours. It also needs regular maintenance to reduce the failure rate of the equipment and improve the service life of the ice machine equipment, so that the ice machine equipment can work better for us.

First, the maintenance and cleaning of the unit of Flake Ice Machine 3T: mainly including whether the compressor is on or off frequently; whether the operation has abnormal noise; whether the compressor running high and low pressure is normal; whether the compressor running current is normal; whether the condensing fan motor has vibration; Clean up, do not pile up debris, hinder heat dissipation.

Second, the condenser is cleaned regularly, and the filter of the condenser. The condenser is used once a year (2-3) times for 1-2 months.

Third, regular cleaning and descaling of the inlet pipe, water storage tank, storage refrigerator and baffle of the Flake Ice Machine Aquatic Processing. Basically once a quarter, cleaning the storage refrigerator at the same time, to clear the sewage drain in the storage refrigerator; regularly replace the water inlet filter of the ice machine, the small water will affect the efficiency of ice making; Descaling, uneven water ingress will result in different sizes of ice; periodically check whether the temperature control probe in the refrigerator is normal; regularly remove the scale from the ice sensor; check whether the cover of the refrigerator is sealed. Daily maintenance can not be ignored, it is very important to properly maintain the ice tea shop ice machine, which can effectively extend the service life and ice making effect of the tea shop ice machine.